Logo
Get Estimate

Aluminum Siding Installation in Akron Built to Handle Ohio Weather

Durable, low-maintenance aluminum siding replacement for Akron homes


Aluminum Siding Installation in Akron gives your home a tough, rust-proof shell that shrugs off hail, wind, and freeze-thaw cycles. Whether you're replacing dented panels on a 1960s Firestone Park ranch or upgrading a West Akron two-story, our crew installs aluminum siding that holds its color and shape for decades. We've served Summit County since 2015, and we know exactly how Akron weather treats exterior walls.

Close-up of a modern industrial building with metal siding and roller doors.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed 11+ Years Trusted in Akron

What's Included in Aluminum Siding Installation

Every aluminum siding installation in Akron we quote includes tear-off, disposal, sheathing inspection, house wrap, flashing, panels, trim coil, caulk, and a final walkthrough. Add-ons like new soffit, fascia, gutters, or window wraps get quoted separately so you can see exactly what each piece costs.

Full Tear-Off and Disposal

We remove all old siding, nails, and trim, then haul it away in a roll-off dumpster. The wall gets a clean inspection before anything new goes up. Tear-off typically takes one day on a standard Akron home.

Sheathing Repair

Soft or rotted sheathing gets cut out and replaced with new OSB or plywood. We photograph every repair so you can see what was behind the old siding. Most Akron homes need one to three small patches.

House Wrap and Flashing

We install a weather-resistive barrier over the sheathing and new metal flashing at every window, door, and penetration. This is the layer that actually keeps water out, and it's the step cheap crews skip.

Aluminum Panels and Trim Coil

Factory-finished aluminum panels in your chosen profile and color, plus matching trim coil on corners, J-channels, and window frames. Panels are fastened with slotted nail holes so the metal can move with temperature swings.

Soffit and Fascia (If Quoted)

New aluminum or vinyl soffit and fascia protect the roof edge and vent the attic. We balance intake and exhaust so moisture doesn't build up. Rotted fascia boards get replaced before the new material goes on.

Caulk, Cleanup, and Walkthrough

Every joint gets exterior-grade caulk rated for metal. We run a magnetic sweep for stray nails, haul the dumpster, and walk the property with you. You get a written workmanship warranty before we leave.

What Aluminum Siding Installation in Akron Actually Involves


Aluminum Siding Installation in Akron is the process of removing old exterior cladding, inspecting and repairing the sheathing and house wrap underneath, then fastening new aluminum panels, trim coil, soffit, and fascia to the wall structure. Aluminum arrives pre-finished in baked-on enamel, so it never needs painting unless you want a color change. We cut panels with a circular saw or tin snips, set them with a siding nailer, and lock every course to the one below so the wall sheds water instead of trapping it.

Akron homes take a beating. Lake-effect snow dumps moisture on roofs, summer hail dents cheap vinyl, and the freeze-thaw cycle between December and March works nails loose. If you've been searching for aluminum siding installation near me Akron OH, you're probably tired of patching cracked panels or watching your energy bills climb because the old siding has no backing. Aluminum goes up fast, resists dents better than thin vinyl, and reflects heat instead of soaking it in.

Our Aluminum Siding Installation Process

Every job follows the same five-step sequence. No surprises, no mystery invoices, no crews that disappear for a week. Here's exactly what happens from the first phone call to the final walkthrough.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and Methods We Use for Aluminum Siding

Tools & Equipment

Siding Nailer

Drives nails to consistent depth without over-driving. Over-driven nails crack panels and cause buckling, so we set the tool carefully and check depth every few courses.

Circular Saw and Tin Snips

Circular saw with a fine-tooth blade for long straight cuts, tin snips for notching around windows, doors, and penetrations. Clean cuts mean tight overlaps and no gaps.

Chalk Line and 4-Foot Level

Establishes a perfectly level starter course. If the first course is off, every course above it is off. We snap a chalk line and verify with a level before nailing anything.

Caulking Gun with Exterior-Grade Caulk

Seals every joint, corner, and penetration. We use caulk rated for metal and freeze-thaw cycles, not the cheap stuff that cracks after one winter.

Pry Bar and Siding Removal Tool

Pulls old siding and nails without damaging the sheathing underneath. Careful removal saves us from unnecessary sheathing repairs and keeps the job on schedule.

Scaffolding and Ladders

Safe access to second-story walls and gables. We set scaffolding on stable ground and use ladder stabilizers to protect gutters and landscaping.

Methods & Standards

VSI Installation Standards

We follow Vinyl Siding Institute guidelines for fastener spacing, panel overlap, and clearance at openings. The same standards apply to aluminum because the drainage and expansion principles are identical.

EPA Lead-Safe Work Practices

On pre-1978 Akron homes, we contain the work area with plastic sheeting, use HEPA vacuums, and follow EPA lead-safe protocols for removal and disposal. Required by federal law, and we do it on every qualifying job.

Slotted Nail Hole Fastening

Aluminum expands and contracts with temperature. We nail through the center of the slotted holes and leave the panel free to move. This prevents the buckling and oil-canning that shows up on poorly installed jobs.

Rainscreen and House Wrap Detail

We install house wrap with proper overlap and tape every seam. At windows and doors, we layer flashing so water sheds outward. This is the detail that keeps Akron's freeze-thaw cycle from rotting your sheathing.

When Akron Homeowners Call Us for Aluminum Siding

01

A 1960s ranch in Firestone Park with original aluminum siding that's been dented by decades of hail.

What we do: We tear off the old panels, inspect and repair the sheathing, install new house wrap and flashing, then hang fresh aluminum in a modern color. Full job takes four days.

→ The house looks 40 years younger, and the new siding carries a 30-year manufacturer finish warranty.

02

A two-story in West Akron with wood siding that needs painting every four years and shows signs of rot near the foundation.

What we do: We remove the wood siding, replace rotted sheathing, and install aluminum with trim coil on all corners and window frames. No more scraping or priming.

→ The homeowner saves $3,000 to $4,000 per repaint cycle and gets a wall that handles Akron winters without swelling or cracking.

03

A rental property near University Park with peeling vinyl siding and repeated tenant complaints about drafts.

What we do: We install aluminum siding with reflective house wrap and new soffit to improve attic ventilation. Work is scheduled between tenant turnovers to avoid disruption.

→ Tenant complaints stop, energy bills drop, and the landlord gets a maintenance-free exterior for the next 30 years.

04

A home in Merriman Valley with storm damage from a summer hail event and an insurance claim already filed.

What we do: We document the damage with photos, work directly with the adjuster, and complete the aluminum siding replacement once the claim is approved. Most jobs start within a week of approval.

→ The homeowner pays only the deductible, and the new siding matches the original profile and color.

How Aluminum Siding Installation Runs in Akron

Akron sits in a freeze-thaw belt that swings from single digits in January to the 90s in July. That temperature range is brutal on exterior cladding. Aluminum handles it better than most materials because it moves with the wall instead of fighting it, but only if it's fastened correctly. We nail through slotted holes and leave expansion room at every panel end. Summit County also has a lot of pre-1978 housing stock, which means EPA Lead-Safe protocols apply on most of our jobs. We're certified for that work, and we handle the containment and disposal without adding drama to your week. If you're comparing the cost of aluminum siding installation in Akron Ohio against vinyl or fiber cement, remember that aluminum's 30-to-40-year lifespan and zero repainting usually wins on total cost of ownership. We schedule most jobs in spring and fall when temperatures sit between 50 and 75 degrees, which is the ideal range for caulk cure and panel expansion. Winter installs are possible, but we watch the forecast and won't caulk below 40 degrees.

Neighborhoods We Serve

  • Firestone Park

    Heavy concentration of 1950s and 1960s ranches with original aluminum siding. Most need full replacement, and we've done dozens on these exact floor plans.

  • Highland Square

    Older two- and three-story homes with complex trim and gable details. Aluminum works well here, but the job takes longer because of all the cuts and trim coil work.

  • West Akron

    Mix of wood and vinyl siding on mid-century homes. Many homeowners switch to aluminum to escape the repainting cycle every four to five years.

  • University Park

    Rental-heavy neighborhood where landlords want low-maintenance exteriors. Aluminum siding holds up to tenant turnover and never needs painting.

  • Merriman Valley

    Tree-heavy lots mean more debris impact and shade-related algae growth. We install aluminum with a factory finish that resists chalking and fading.

Local Conditions We Plan For

  • Freeze-thaw cycles from December through March

    Water gets behind loose panels, freezes, and pushes them further out. Proper flashing and slotted fastening prevent this. We inspect every wall for existing freeze damage before quoting.

  • Summer hail events across Summit County

    Hail dents aluminum, but it rarely punctures it. Dented panels can often be replaced individually instead of re-siding the whole house. We keep color-matched panels on hand for common profiles.

  • Pre-1978 housing stock triggers EPA Lead-Safe rules

    We contain the work area, use HEPA filtration, and dispose of old material per federal guidelines. This adds a day to some jobs but keeps your family safe and your project legal.

  • Lake-effect moisture and humidity

    Walls stay damp longer, which accelerates rot behind failing siding. House wrap and proper flashing are non-negotiable on Akron installs. We never skip these steps to save a buck.

Firestone Park Ranch Full Replacement

Before

A 1962 ranch with original aluminum siding that had 40-plus dents, two soft spots in the sheathing, and peeling caulk at every window. The homeowner had patched it three times and was tired of chasing leaks.

After

New aluminum siding in a slate gray finish, fresh house wrap, new flashing at all openings, and trim coil on every corner. Job took four days. The homeowner reported a 12-degree drop in upstairs summer temperature.

Maintenance: Rinse with a garden hose twice a year. No painting needed for 25 to 40 years. Check caulk joints at windows every few years and touch up if they crack.

Before

A two-story colonial with cedar siding that needed painting every four years. Rot had started at the foundation line, and the last paint job cost $4,200. The homeowner wanted off the repainting treadmill.

After

Full tear-off, sheathing repair at the foundation, new house wrap, and aluminum siding in a warm beige. Trim coil on all 14 windows. Job took six days. The homeowner saved the next paint cycle entirely.

Maintenance: Wash annually with mild soap. Inspect the foundation line each spring for any sign of moisture. Aluminum won't rot, but the sheathing behind it still needs to stay dry.

Before

A duplex near the university took hail damage on the west wall. Insurance approved a partial replacement, but the original siding color was discontinued. The landlord needed a match that wouldn't look patched.

After

We replaced the entire west wall with new aluminum in a close-match color and blended the transition at the corner trim. Job took two days. The adjuster approved the full-wall scope after seeing the color mismatch.

Maintenance: Keep gutters clear so water doesn't splash up onto the lower panels. Check the corner trim after big storms. If a panel dents, we can swap it individually.

Problems Aluminum Siding Installation Solves for Akron Homes

Old siding fails in predictable ways, and Akron's weather speeds up the timeline. Here are the four problems we fix most often, and what happens if you let them ride.

Problem

Dented aluminum siding from hail and wind

Dents look bad, but the real issue is what they hide. Loose panels let water behind the wall, which rots sheathing and invites pest infestation.

Our Fix

We tear off the damaged panels, inspect the sheathing, and install new aluminum with a fresh weather barrier. If the dents are isolated, we can do a partial replacement and match the color as closely as possible.

Problem

Peeling and cracking siding on pre-1978 homes

Cracked siding exposes lead paint underneath, which becomes a hazard when it flakes. It also lets water in, driving up energy bills and repair costs.

Our Fix

As an EPA Lead-Safe Certified firm, we handle pre-1978 homes by the book. We contain the work area, remove old material safely, and install new aluminum siding that never needs repainting.

Problem

High energy bills from poor wall insulation

Old siding with no backing lets heat escape in winter and soak in during summer. Akron homeowners often see $80 to $150 per month in avoidable energy costs.

Our Fix

We install reflective house wrap under the new aluminum and can add foam board insulation if you want more R-value. Most customers report a noticeable drop in heating and cooling costs the first season.

Problem

Water infiltration behind loose siding panels

Water gets in, freezes, and pushes panels further out. Over a few winters you end up with rotted sheathing, mold, and ice dam damage at the roofline.

Our Fix

We remove the loose panels, replace any rotted sheathing, install new flashing and house wrap, and reinstall aluminum with proper overlap and fastening. The wall drains correctly from that point forward.

Why Akron Homeowners Choose Aluminum Siding

Why Akron Homeowners Choose Aluminum Siding

Aluminum siding delivers a combination of durability, low maintenance, and curb appeal that few other materials match in Northeast Ohio's climate. Here are the four biggest wins our customers report.

  • Rust-Proof and Dent-Resistant

    Aluminum forms its own oxide layer, so it never rusts the way steel does. It dents under a direct hammer blow, but it shrugs off the hail and wind-driven debris that flatten cheap vinyl. For Akron homes in storm-prone ZIP codes like 44305 and 44306, that toughness means fewer repair calls.

  • No Painting Required

    Factory-baked enamel holds color for 25 to 40 years. You'll never scrape, prime, or repaint unless you want a new shade. That saves Akron homeowners $2,000 to $5,000 per repaint cycle, and it eliminates the lead-safe concerns that come with old wood siding on pre-1978 homes.

  • Lower Cooling Bills

    Aluminum reflects solar radiation instead of absorbing it. When we add a reflective house wrap underneath, attic temperatures drop 8 to 12 degrees on a July afternoon. Akron summers aren't Phoenix-hot, but the savings add up over a 30-year service life.

  • Fast Installation, Clean Jobsite

    A typical 1,500-square-foot Akron home gets full aluminum siding replacement in three to five days. We tear off, inspect, wrap, and install in one continuous push. You get a magnetic sweep of the yard, a dumpster haul-away, and a walkthrough before we pull out of the driveway.

Licensed, Certified, and Reviewed

Licensed & Certified

  • EPA Lead-Safe Certified Firm — issued by U.S. Environmental Protection Agency
  • State of Ohio Contractor License — issued by Ohio Construction Industry Licensing Board
  • BBB Accredited Business — issued by Better Business Bureau of Akron
  • OSHA 10 Trained Crew — issued by Occupational Safety and Health Administration
  • Vinyl Siding Institute Certified Installer — issued by Vinyl Siding Institute

Verified Reviews

Google ★★★★★4.9

Apex replaced the aluminum siding on our Firestone Park ranch. Crew was on time every day, cleaned up each evening, and the price matched the quote exactly. Two winters in and no issues with the panels or caulk.

BBB ★★★★★5.0

We got three quotes for aluminum siding replacement and Apex was the only one that explained house wrap and flashing. They found rotted sheathing, showed us photos, and fixed it for a fair price. Highly recommend.

Yelp ★★★★★4.8

Had hail damage on our West Akron home and Apex handled the insurance paperwork with us. New aluminum siding went up in five days. Color match on the trim coil is perfect. Would use them again.

Google ★★★★★5.0

I own rentals near University Park and needed low-maintenance siding. Apex installed aluminum on three buildings over one summer. Tenants stopped calling about peeling paint. Best money I've spent on the properties.

11 Years Installing Siding in Summit County

Apex Siding Akron has been installing exterior cladding since 2015. In that time we've completed hundreds of aluminum siding projects across Summit County, from single-story bungalows in Sherbondy Hill to three-story Victorians in Highland Square. Our installers hold EPA Lead-Safe Certification, which matters on any Akron home built before 1978, and we follow Vinyl Siding Institute installation standards even on aluminum jobs because the flashing and drainage details are identical. We're a State of Ohio licensed contractor and BBB Accredited. Every crew member is OSHA 10 trained, and we carry full liability and workers' comp coverage.

  • EPA Lead-Safe Certified firm, required for pre-1978 Akron housing stock
  • State of Ohio licensed contractor with continuous coverage since 2015
  • OSHA 10 trained installers on every crew, no subcontractors
  • Hundreds of completed aluminum and vinyl siding projects in Summit County
  • BBB Accredited business with an A rating and zero unresolved complaints
Get Started Today
11 Years Installing Siding in Summit County

What Akron Homeowners Say

Real experiences from customers who chose our Aluminum Siding Installation services.

“Our 1962 ranch had the original aluminum siding and it was dented to hell from decades of hail. Apex tore it off, found two soft spots in the sheathing, fixed them, and had new aluminum up in four days. Color match on the trim coil is dead-on. Price came in exactly where the quote said.”

D

Dave R.

Homeowner, Firestone Park

“We got four quotes for aluminum siding replacement and Apex was the only one that explained the house wrap and flashing details. The crew was respectful, cleaned up every night, and the magnetic sweep caught nails I never would have found. Two winters in and no issues.”

M

Maria T.

Homeowner, Highland Square

“I own three rentals near the university and needed siding that wouldn't need painting every few years. Apex installed aluminum on all three over one summer. Tenants stopped calling about peeling paint, and the buildings look sharper than anything else on the block.”

K

Ken W.

Landlord, University Park

Frequently Asked Questions About Aluminum Siding in Akron

Real answers to the questions we hear most often from local homeowners and property managers.

How much does aluminum siding installation cost in Akron OH?
Most Akron homeowners pay $8,000 to $18,000 for a full aluminum siding replacement in 2026, or roughly $7 to $12 per square foot installed. A 1,200-square-foot ranch lands near the low end; a 2,500-square-foot two-story with complex trim pushes toward the top. Tear-off, house wrap, soffit, and fascia are included in our quotes.
How long does aluminum siding last in Akron Ohio?
Expect 30 to 40 years with basic maintenance. Akron's freeze-thaw cycle is the main stressor, so we fasten panels with slotted nail holes that let the metal expand and contract without buckling. Repainting every 15 to 20 years extends the life further. Hail can dent it, but dents don't compromise the weather barrier.
Is aluminum siding good for Akron homes?
Yes, especially on older homes in Firestone Park, Kenmore, and Sherbondy Hill where the original aluminum is already 50-plus years old. It's lightweight, rust-proof, and handles hail better than thin vinyl. The one trade-off is denting, so we recommend it for walls that aren't in a direct impact zone from a driveway or basketball hoop.
Can you paint aluminum siding in Akron OH?
Absolutely. Factory finish lasts decades, but if you want a new color, aluminum takes paint well after a good cleaning and a bonding primer. We use 100 percent acrylic exterior paint rated for metal. A typical Akron home takes 15 to 25 gallons and two to three days of prep and spraying.

Other Siding Services We Offer in Akron

Siding Replacement

Full tear-off and replacement of any exterior cladding. If your aluminum siding is too far gone to repair, we swap it for new aluminum or upgrade to a different material. Same crew, same fixed-price approach.

View Siding Replacement

Vinyl Siding Installation

Vinyl costs less upfront than aluminum and comes in more colors. It's a good fit for Akron rentals and budget-conscious homeowners. We install CertainTeed and Mastic vinyl with the same flashing and wrap details we use on aluminum.

View Vinyl Siding Installation

Fiber Cement Siding Installation

James Hardie fiber cement is the premium upgrade. It won't dent, holds paint for 15 years, and looks like real wood. Many Akron homeowners pair fiber cement on the front facade with aluminum on the sides to control cost.

View Fiber Cement Siding Installation

Wood Siding Installation

Cedar and pine siding for homeowners who want a natural look. We install with a rainscreen gap and back-priming to fight Akron's humidity. Higher maintenance than aluminum, but the curb appeal is unmatched on historic homes.

View Wood Siding Installation

Engineered Wood Siding Installation

LP SmartSide gives you the look of wood with better moisture resistance. It's a strong middle ground between vinyl and fiber cement. We install it with the same trim coil and flashing details we use on aluminum jobs.

View Engineered Wood Siding Installation

Stone Veneer Siding Installation

Real or manufactured stone for accent walls, entryways, and chimneys. Pairs well with aluminum siding on the rest of the house. We handle the lath, scratch coat, and weep screed so moisture drains correctly.

View Stone Veneer Siding Installation

Get Your Aluminum Siding Installation in Akron Quote Today

We'll inspect your exterior, show you samples, and hand you a fixed price the same day. No pressure, no follow-up calls every week. Licensed, insured, and serving Akron since 2015. Call (330) 567-4711 or request a free estimate online.

Call (330) 567-4711 Get Free Estimate

Contact Apex Siding Akron

Call (330) 567-4711 or email info@apexsidingakronoh.com and we will get back to you the same business day. We answer the phone Monday through Friday, 8 a.m. to 6 p.m., and we check messages Saturday morning. Storm damage after hours? Leave a message and we will call you first thing.

Or call us right now at (330) 567-4711 — we answer.

Apex Siding Akron oh


  • Address

    1789 Killian Rd, Akron, OH 44312

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call (330) 567-4711 Get Quote
Call Quote