Logo
Get Estimate
How-To GuidesLocal Guides

How to Install Stone Veneer Siding on Your Home


Learn how to install stone veneer siding on your Akron home, from surface prep and lath to mortar and curing, plus local costs and when to hire a pro.

AApex Siding Akron OH ·November 2026 ·10 min read
Charming blue house exterior with modern architectural features in Asheville, NC.

You can install stone veneer siding on your home by fastening a weather-resistant barrier and metal lath to the wall, applying a scratch coat of mortar, then bedding each stone in mortar with a consistent 3/8-inch joint. The work is heavy and wet, but it is within reach for a confident DIYer with the right tools and two full weekends. This guide walks through the exact sequence, the 2026 costs in Akron, and the spots where most homeowners get into trouble.

What Stone Veneer Siding Actually Is

Stone veneer siding is a manufactured or natural stone facing, typically 1 to 2.5 inches thick, that hangs on a wall over a drainage plane and mortar bed rather than supporting its own weight like a structural stone wall. It goes on porches, accent walls, chimney chases, and full facades.

The critical distinction is between manufactured veneer (cast concrete or lightweight aggregate, 8 to 15 pounds per square foot) and natural thin stone (real stone cut thin, 12 to 18 pounds per square foot). Both install the same way, but natural stone needs a heavier scratch coat and more careful handling because it varies in thickness.

In Akron, the freeze-thaw cycle is the real enemy. Summit County swings from single digits in January to the 90s in July, and any water that gets behind the veneer and freezes will pop stones off the wall. That is why the weather-resistant barrier and weep screed at the bottom are not optional here. If your existing wall is failing, it may be worth looking at Siding replacement Akron OH before you cover it with stone.

Tools and Materials You Will Need

Gather everything before you start. A stone veneer job that stalls halfway through a scratch coat is a stone veneer job that fails.

  • Hammer drill with a 3/16-inch masonry bit and a 1/4-inch bit for lath
  • Angle grinder with a diamond blade for cutting stone
  • Mortar hoe, mixing tub, and a 1/2-inch drill with a paddle mixer
  • Mason's trowel, pointing trowel, and a jointing tool
  • Staple gun for the weather barrier, tin snips for lath
  • Type S mortar (not Type N - Type S has higher compressive strength and handles Akron winters better)
  • Corrosion-resistant lath, 2.5 lb per square yard minimum
  • Weep screed, flashing tape, and a self-adhering membrane for transitions
  • Safety glasses, N95 respirator, and cut-resistant gloves

Budget $400 to $700 in tools if you are starting from zero. Materials for a 200-square-foot accent wall run $1,200 to $2,000 depending on whether you choose manufactured or natural stone.

Step-by-Step Installation

Work top to bottom on the prep, bottom to top on the stone. That order matters because water has to be able to drain out the bottom of the assembly.

1. Prep the substrate

Strip the wall back to sheathing or existing masonry. If you are going over brick or block, grind the surface flat and remove any loose material. Wood sheathing needs a minimum 7/16-inch thickness and should be solid - if it flexes when you push on it, replace it first.

2. Install the weather-resistant barrier

Staple a WRB (house wrap or two layers of Grade D paper) over the sheathing, lapping horizontal seams 6 inches and vertical seams 12 inches. Run it from the top of the stone area down past the bottom edge. Tape all penetrations.

3. Flash and set the weep screed

At the bottom of the stone area, install a weep screed so water can escape. This is the single most skipped step in DIY stone veneer, and it is the one that causes the most callbacks. Flash window sills, door heads, and any penetration with self-adhering membrane.

4. Fasten the lath

Staple or screw corrosion-resistant lath over the WRB with the cups facing up. Overlap sheets 2 inches and fasten every 6 inches vertically and 16 inches horizontally. Keep lath at least 1/4 inch clear of the weep screed so water can drain.

5. Apply the scratch coat

Mix Type S mortar to a peanut-butter consistency and trowel it over the lath to a nominal 1/2 inch. Work it into the lath with the flat of the trowel, then rake horizontal grooves so the next coat has something to bite. Let it cure 24 to 48 hours, keeping it damp the first day.

6. Set the stone

Start at the bottom and work up. Butter the back of each stone with mortar and press it into the scratch coat with a slight twisting motion. Maintain a consistent 3/8-inch joint. For large stones, add a small shim or a screw through the lath to hold the stone until the mortar sets.

7. Point the joints

Once the mortar has set enough to hold a thumbprint but not smear, tool the joints with a jointing tool or a wooden dowel. Do not overwork the mortar - you will pull it out of the joint.

8. Cure and seal

Keep the wall damp for 48 hours and out of direct sun if possible. After 28 days, apply a breathable masonry sealer. Do not seal sooner - trapped moisture has to escape.

How Long Does Stone Veneer Siding Installation Take in Akron?

A 200-square-foot accent wall takes a competent DIYer 3 to 5 full days spread over two weekends, including cure time. A full facade of 1,200 square feet takes a two-person crew 10 to 14 working days.

Weather is the wild card in Akron. Mortar needs to stay above 40°F for 48 hours after application. That rules out most of December through February for exterior work unless you tent and heat the wall. April through October is the practical window. If you are scheduling around other exterior work, our Siding installation in Highland Square crews see the same seasonal squeeze every spring.

What Is the Cost to Install Stone Veneer Siding in Akron?

Typical 2026 pricing in the Akron area runs $12 to $22 per square foot installed for manufactured veneer and $20 to $35 per square foot for natural thin stone. A 200-square-foot accent wall lands between $2,400 and $4,400 installed.

DIY material costs run roughly half that - $1,200 to $2,000 for the same wall - but you supply the labor, the tools, and the warranty. Add $300 to $600 if you need scaffolding or a lift for second-story work.

For comparison, Vinyl siding installation Akron OH runs $6 to $11 per square foot installed, and Fiber cement siding installation Akron OH runs $9 to $16. Stone veneer is the premium option, and it shows in the resale value on Akron's older housing stock.

Common Mistakes to Avoid

The failures we see on DIY stone veneer jobs almost always trace back to water management, not stone placement. Get the drainage right and the wall lasts decades.

  • No weep screed. Water pools at the bottom of the assembly, freezes, and pushes the bottom course off the wall.
  • Lath installed upside down. The cups must face up so the scratch coat keys in. Flat-side-out lath sheds the mortar.
  • Scratch coat too thin. Under 3/8 inch and the stone will not have enough to grab. Over 3/4 inch and it sags off the lath.
  • Type N mortar. It is softer and more permeable. Type S is the standard for exterior veneer in this climate.
  • Sealing too early. Sealer on green mortar traps moisture and causes efflorescence or spalling.
  • Ignoring flashing at penetrations. Every hose bib, light fixture, and outlet needs membrane behind it.

We also see homeowners skip the wall inspection before covering it. If you have rot, loose sheathing, or failing trim, that has to be fixed first. Our Siding repair Akron OH team handles those repairs before any veneer goes on.

When to Call a Professional

Call a professional when the wall is above the first story, when the area exceeds 300 square feet, or when you are covering a chimney or structural column. Those jobs need scaffolding, a two-person crew, and an eye for load and drainage that comes from repetition.

We also get calls when a DIY job has already gone wrong - stones popping off after one winter, efflorescence blooming through the face, or a wall that sounds hollow when you tap it. Those are drainage failures, and they get worse every freeze-thaw cycle.

Apex Siding Akron OH installs stone veneer across Summit County, and we handle the flashing, lath, and scratch coat as one system so the wall drains the way it should. If you want a straight answer on whether your project is a DIY job or a pro job, we will tell you.

Frequently Asked Questions

How do I install stone veneer siding in Akron OH?

Fasten a weather-resistant barrier and corrosion-resistant lath to the wall, apply a 1/2-inch Type S mortar scratch coat, then bed each stone in mortar with a 3/8-inch joint. Finish with a weep screed at the bottom and cure for 48 hours before sealing.

Can I install stone veneer siding myself in Akron Ohio?

Yes, for single-story accent walls under 300 square feet. Above that, or on second stories, the scaffolding, weight, and drainage details make a pro crew the safer and often cheaper choice once you factor in tools and rework.

What is the cost to install stone veneer siding in Akron?

In 2026, expect $12 to $22 per square foot installed for manufactured veneer and $20 to $35 for natural thin stone. A 200-square-foot accent wall runs $2,400 to $4,400 installed, or roughly half that in materials for DIY.

How long does stone veneer siding installation take in Akron?

A 200-square-foot accent wall takes a DIYer 3 to 5 working days across two weekends, including cure time. A full facade of 1,200 square feet takes a two-person crew 10 to 14 working days, weather permitting.

What tools do I need for stone veneer siding in Akron OH?

A hammer drill, angle grinder with diamond blade, mortar hoe, mixing paddle, mason's trowel, jointing tool, staple gun, and tin snips. Add safety glasses, an N95 respirator, and cut-resistant gloves. Budget $400 to $700 if you are buying everything new.

Get Help with Siding Installation in Akron

If your stone veneer project is bigger than a weekend, or if you want the drainage details done right the first time, we can help. Call Apex Siding Akron OH at (330) 567-4711 and we will walk your wall, give you a straight price, and get it on the schedule.

Tagged with

#stone veneer#siding installation#akron ohio#diy#exterior remodeling

Common Questions

How do I install stone veneer siding in Akron OH?
Fasten a weather-resistant barrier and corrosion-resistant lath to the wall, apply a 1/2-inch Type S mortar scratch coat, then bed each stone in mortar with a 3/8-inch joint. Finish with a weep screed at the bottom and cure for 48 hours before sealing.
Can I install stone veneer siding myself in Akron Ohio?
Yes, for single-story accent walls under 300 square feet. Above that, or on second stories, the scaffolding, weight, and drainage details make a pro crew the safer and often cheaper choice once you factor in tools and rework.
What is the cost to install stone veneer siding in Akron?
In 2026, expect $12 to $22 per square foot installed for manufactured veneer and $20 to $35 for natural thin stone. A 200-square-foot accent wall runs $2,400 to $4,400 installed, or roughly half that in materials for DIY.
How long does stone veneer siding installation take in Akron?
A 200-square-foot accent wall takes a DIYer 3 to 5 working days across two weekends, including cure time. A full facade of 1,200 square feet takes a two-person crew 10 to 14 working days, weather permitting.
What tools do I need for stone veneer siding in Akron OH?
A hammer drill, angle grinder with diamond blade, mortar hoe, mixing paddle, mason's trowel, jointing tool, staple gun, and tin snips. Add safety glasses, an N95 respirator, and cut-resistant gloves. Budget $400 to $700 if you are buying everything new.

Ready for Stone Veneer Siding Installation in Akron?

We install stone veneer across Summit County with the flashing, lath, and scratch coat done as one system. Call us for a straight price on your wall.

Call (330) 567-4711 Send a Message
Call (330) 567-4711 Get Quote
Call Quote