Logo
Get Estimate

Soffit and fascia installation Akron OH that seals your roofline

Vented soffit, solid fascia, and trim that outlasts Ohio weather


Soffit and fascia installation Akron OH homeowners can count on starts with the right materials and a crew that measures twice. We replace rotted fascia boards, cut in proper intake vents, and wrap every edge in coil stock that sheds water instead of soaking it up. If your gutters are pulling loose or you spot peeling paint along the rake, call us at (330) 567-4711 for a same-day look.

A worker using a drill to install window blinds in an indoor setting.
Licensed Licensed & Bonded
Fully Insured Insured & Bonded
24/7 Emergency Same-Day Response
Warranty Backed 11+ Years Trusted in Akron

What our soffit and fascia work includes

Every full soffit and fascia replacement in Akron we sell covers tear-off, rafter inspection, new fascia board, vented soffit, trim coil, and gutter reset. Add-ons like full gutter replacement, fascia-mounted lighting, or porch ceiling rebuilds are quoted separately so you can see exactly what you are paying for.

Tear-off and disposal

We remove the old fascia, soffit panels, and any failed trim, then haul it away. The deck and rafter tails get swept clean so we can inspect the wood before anything new goes up. Disposal is included in the price.

Rafter tail inspection

Every rafter tail along the roofline gets probed for soft wood. Anything that fails gets sistered with fresh lumber or replaced. This is the step that keeps a new fascia line straight for the next 20 years.

New fascia board and coil

We install solid fascia board sized to carry your gutters, then wrap it in trim coil with a folded drip edge. Corners are mitered and caulked, not overlapped, so water has nowhere to wick in.

Vented soffit panels

Soffit panels are cut to fit each bay and installed with the vent pattern facing down. We aim for roughly 50 percent net free area so the attic pulls air properly. Solid panels go on porch ceilings and gable returns.

Gutter reset and hose test

Your existing gutters get rehung level with the correct pitch toward the downspouts. We run water through the longest run and watch it drain. If a hanger is shot, we replace it on the spot.

Site cleanup and walkthrough

Magnets sweep the lawn for nails and screws. You walk the finished roofline with the crew lead, and any punch-list item gets handled before we pull out of the driveway. No callbacks needed.

Soffit and fascia installation Akron OH, explained


Soffit and fascia installation Akron OH is the exterior trade that closes the gap between your roof edge and your wall. The soffit is the underside panel you see when you stand on the porch and look up; the fascia is the vertical board the gutters screw into. Together they carry the weight of your gutter system, feed air into the attic, and keep rain, squirrels, and wasps out of the rafter bays. We install vented aluminum and vinyl soffit panels, solid or vented fascia, and matching trim coil on rake edges, porch ceilings, and dormers.

Most Akron homes we inspect were built between 1915 and 1975, so the original wood fascia has had decades of freeze-thaw cycles working on it. Water backs up behind clogged gutters, the board softens, and by the time you notice the sag, the rafter tail is wet too. That is why soffit and fascia replacement Akron projects usually start with a moisture probe, not a sales pitch. If you have been searching for soffit and fascia installation near me Akron OH, we can walk the roofline with you and show you exactly where the damage starts.

How our soffit and fascia process runs

Five steps, start to finish, usually wrapped in two to four days on a standard Akron house. You get a written scope before we start and a walkthrough when we are done.

01

Schedule

Call or book online — a real human picks up and confirms a 2-hour arrival window.

02

Diagnose

Licensed tech inspects on-site, then walks you through the cause and your options.

03

Fix

The job is completed to code and done right the first time — no shortcuts, no surprises.

04

Guarantee

Every job backed by a written workmanship warranty — and we stand behind it.

Tools and methods we use

Tools & Equipment

Siding nailer

Drives fasteners to a consistent depth so vinyl and aluminum panels can expand and contract without buckling. We set the pressure per material, not per job.

Tin snips and trim brake

Cuts and bends trim coil on site for rake edges, corners, and drip edges. On-site bending means the coil fits your actual roofline instead of a stock length.

Chalk line and 4-foot level

Keeps the fascia line straight across the full run of the house. A fascia that is off by a quarter inch shows up as a wavy gutter line from the street.

Moisture meter

Probes fascia boards and rafter tails for hidden moisture before we cover anything. It is how we decide what gets replaced and what can stay.

Pry bar and siding removal tool

Pulls old panels and trim without damaging the siding above or the wall behind it. Clean removal saves material and labor on the reinstall.

Scaffolding and ladders

Gets the crew safely to second-story rooflines and porch ceilings. We set scaffolding on two-story jobs rather than working off extension ladders all day.

Caulking gun with exterior caulk

Seals every joint, corner, and penetration with caulk rated for exterior use. This is what keeps water and insects out of the rafter bays long term.

Methods & Standards

Vented soffit with 50 percent net free area

We cut vented panels so the intake area balances the ridge vent on top. That balance is what actually moves hot attic air out in summer and keeps the roof deck cold in winter. Too little intake and the ridge vent does nothing.

Folded drip edge on trim coil

The bottom edge of the fascia coil gets folded into a drip edge rather than left flat. Water sheds off the fold and clears the wall below, which is the difference between a dry wall and a stained one after a hard rain.

Rafter tail sistering

When a rafter tail is soft but the rest of the rafter is sound, we nail a new piece of lumber alongside it. That restores the nailing surface for the fascia without opening up the roof, and it costs far less than a full rafter replacement.

Vinyl Siding Institute installation standards

We follow VSI guidance on fastener placement, panel overlap, and clearance at corners and openings. Those details are what let a panel move with temperature changes instead of cracking or oil-canning.

EPA Lead-Safe work practices

On homes built before 1978, we follow EPA Lead-Safe Certified procedures during tear-off. Containment, cleanup, and disposal are handled to the standard, which matters on a lot of older Akron housing stock.

When Akron homeowners call us

01

A homeowner in West Akron is getting new siding and the contractor flagged the fascia as soft during the estimate.

What we do: We scope the soffit and fascia work alongside the siding so both are done in one mobilization. The crew tears off the old fascia, repairs two rafter tails, and installs new vented soffit and trim coil that matches the new panels.

→ One setup, one cleanup, and a roofline that matches the new siding instead of dragging it down.

02

A Firestone Park bungalow has gutters that pull loose every winter and stain the brick below.

What we do: We replace the fascia board, install new hangers, and reset the gutter pitch toward the downspouts. The drip edge on the new trim coil throws water clear of the wall.

→ The gutters stay put through freeze-thaw, and the brick staining stops.

03

A two-story in Chapel Hill has squirrels in the attic and visible gaps at the soffit joints.

What we do: We pull the old panels, seal the openings, and install new vented soffit with tight miters. Scaffolding is set up for the second story so the crew can work safely and reach every bay.

→ The attic is sealed, the scratching stops, and the intake ventilation is corrected at the same time.

04

A homeowner in Riverside is selling in the spring and wants the exterior to photograph well.

What we do: We replace the peeling fascia and chalky soffit, match the trim coil to the existing siding, and reset the gutters. The work takes two days and does not disturb the siding.

→ The listing photos show a clean, finished roofline instead of peeling paint and sagging gutters.

How soffit and fascia work runs in Akron

Akron sits in a freeze-thaw belt that punishes rooflines. We get snow, then a 45-degree day, then a hard freeze again, and that cycle repeats all winter. Water finds every gap in the fascia, freezes, and pries it open a little wider each time. The housing stock makes it worse: most of the city was built before 1975, so the original fascia boards are 50 to 100 years old and many have been repainted a dozen times. When we open up a roofline in Firestone Park or Sherbondy Hill, we expect to find at least one soft rafter tail per side. Our approach is to repair the wood first, then cover it with trim coil that will not need repainting. Summit County also enforces standard building codes on ventilation and egress, so we size soffit intake to match the attic volume rather than guessing. If you have been searching for the best soffit and fascia installer Akron OH has on call, the difference usually shows up in what happens under the panels, not on top of them.

Neighborhoods We Serve

  • Firestone Park

    Lots of 1920s bungalows with original wood fascia and low-pitch roofs. We see more rafter tail rot here than anywhere else in the city.

  • Highland Square

    Older two-stories with deep eaves and porch ceilings. The porch soffit usually needs replacing at the same time as the main roofline.

  • Merriman Valley

    Tree cover keeps gutters full of leaves, which backs water up behind the fascia. Fall gutter cleaning matters more here than in open neighborhoods.

  • West Akron

    Mix of mid-century ranches and newer builds. On the ranches, we often find aluminum soffit that has chalked out and needs full replacement.

  • Chapel Hill

    Two-story homes where scaffolding is required. We set up properly rather than working off ladders, which keeps the crew safe and the fascia line straight.

Local Conditions We Plan For

  • Freeze-thaw cycles from December through March

    Water works into every fascia joint and expands when it freezes. This is the main driver of fascia rot in Akron, and it is why we fold a drip edge into the trim coil instead of leaving a flat edge.

  • Heavy oak and maple canopy in older neighborhoods

    Gutters fill with leaves twice a year, and backed-up water sits against the fascia. We recommend gutter guards or a fall cleaning schedule on homes with mature trees overhead.

  • Pre-1978 housing stock across most of the city

    Lead paint is present on many original fascia boards. Our EPA Lead-Safe Certified crew handles containment and disposal to standard on every job that triggers the rule.

  • Summer hail and straight-line wind storms

    Dented fascia coil and torn soffit panels are common after a storm. We document the damage with photos so your insurance claim has what it needs.

Firestone Park bungalow roofline rebuild

Before

Original 1924 wood fascia was split along the entire back run, and two rafter tails were soft enough that a screwdriver sank in an inch. The gutters had pulled away and were dumping water against the foundation.

After

We sistered both rafter tails, installed 140 linear feet of new fascia with folded drip edge, and hung 140 linear feet of vented soffit. The gutters were reset level and hose-tested. Total job time was three days.

Maintenance: Clear the gutters each November and check the fascia line every spring for any sign of separation. With the drip edge in place, the coil should not need repainting.

Before

Soffit panels had open joints at every bay, and squirrels had been in the attic for two seasons. The attic ran hot in summer because the intake vents were blocked with nesting material.

After

We pulled all the old panels, cleared the nesting debris, sealed the openings, and installed 165 linear feet of vented soffit with tight miters. Attic temperature dropped measurably on the first hot week after the job.

Maintenance: Walk the perimeter once a year and look for any panel that has worked loose. If you see one, call us and we will resecure it before an animal finds the gap.

Before

The fascia was peeling down to bare wood and the soffit was chalky and cracked. The homeowners were getting new siding and did not want the old roofline dragging down the look of the new panels.

After

We replaced 210 linear feet of fascia and soffit, matched the trim coil to the new siding color, and rebuilt the porch ceiling soffit. The roofline reads as a continuous edge from the street.

Maintenance: Wash the soffit once a year with a garden hose and mild soap. Trim coil does not need paint, so there is no repainting cycle to keep up with.

Roofline problems we fix in Akron

Most of the calls we get start with one visible symptom and turn out to be a roofline issue underneath. Here are the four we see most often on Akron houses.

Problem

Gutters sagging away from the house

Water dumps against the foundation instead of running to the downspouts, which leads to basement dampness and washed-out landscaping beds.

Our Fix

We pull the gutters, replace the soft fascia board behind them, and rehang the gutters level with new hangers. The gutter line ends up straight and the runoff goes where it should.

Problem

Peeling paint and soft wood along the rake

Once the fascia board is wet, paint will not stick no matter how many times you repaint. The rot spreads into the rafter tail and eventually into the roof deck.

Our Fix

We cut out the failed section, sister the rafter tail if needed, and wrap the new board in trim coil. Coil does not need repainting, so the problem stops coming back every few years.

Problem

Ice dams forming at the roof edge

A warm attic melts snow on the roof, the water refreezes at the cold eave, and the ice dam pushes water up under the shingles and into the wall.

Our Fix

Vented soffit gives the attic proper intake airflow, which keeps the roof deck colder and more even. Combined with clear gutters, that is the practical fix for ice dams on most Akron homes.

Problem

Birds and wasps nesting under the eave

Open soffit joints and gaps at the fascia give insects and birds a direct path into the rafter bays, and from there into the attic insulation.

Our Fix

We install continuous soffit panels with tight miters and caulk every penetration. No open joints means no entry point, and the attic stays sealed.

Why Akron homeowners replace soffit and fascia

Why Akron homeowners replace soffit and fascia

Four things a new soffit and fascia system does that paint and caulk never will. Each one shows up on your energy bill, your gutter line, or your attic inspection.

  • Stops water at the edge

    A properly bent fascia cover sheds water into the gutter instead of letting it wick into the rafter tail. We use trim coil with a folded drip edge, so runoff clears the wall by a full inch. That one detail prevents the rot that starts behind 90 percent of the sagging gutters we see in Summit County.

  • Vents the attic correctly

    Intake ventilation matters as much as the ridge vent on top. We cut vented soffit panels to deliver roughly 50 percent net free area, which pulls hot attic air up and out. In July, that can drop your upstairs temperature several degrees and take load off the air conditioner.

  • Keeps pests out of the rafters

    Squirrels, starlings, and wasps all look for a gap at the roofline. A continuous soffit panel with tight miters and no open joints closes that door. We seal every penetration with caulk rated for exterior use, so there is no finger-width gap left for a determined animal to work open.

  • Lifts the whole exterior

    New fascia and soffit sharpen the roofline and make the siding below it look newer. On a typical 1,500 square foot Akron house, we are talking about 120 to 180 linear feet of fascia and matching soffit, which reads as a clean, finished edge from the street and from the sidewalk.

Licensed, insured, and accountable

Licensed & Certified

  • State of Ohio Contractor License — issued by State of Ohio
  • EPA Lead-Safe Certified Firm — issued by U.S. Environmental Protection Agency
  • Vinyl Siding Institute Certified Installer — issued by Vinyl Siding Institute
  • James Hardie Preferred Contractor — issued by James Hardie
  • BBB Accredited Business — issued by Better Business Bureau

Verified Reviews

Google ★★★★★4.9

Showed up when they said they would, walked the roof with me, and pointed out two soft rafter tails I had no idea about. Price matched the invoice. The new fascia and soffit look sharp and the gutters finally drain right.

BBB ★★★★★4.8

We had squirrels in the attic and three other companies just wanted to trap them. Apex found the open soffit joints and fixed the actual problem. No scratching since, and the vented panels dropped our upstairs temperature.

Google ★★★★★5.0

Two-story house in Chapel Hill, so scaffolding was needed. The crew set up properly, kept the site clean, and finished in three days. The trim coil matches our siding perfectly. Would hire again.

Yelp ★★★★★4.7

Called on a Tuesday, had an estimate that afternoon, and the work was done by Friday. They repaired a rafter tail instead of just covering it up, which is more than the last company offered to do. Straight answers the whole way.

Eleven years on Akron rooflines

Apex Siding Akron oh has been working on Summit County exteriors since 2015. That is 11 years of fascia tear-offs, soffit cuts, and gutter resets on houses from Firestone Park bungalows to Merriman Valley two-stories. Our installers are trained on James Hardie and CertainTeed systems, and we hold EPA Lead-Safe certification because a lot of Akron housing stock predates 1978. We work to Vinyl Siding Institute installation standards, which means fasteners, panel overlap, and clearance are done to spec, not to whatever is fastest. When we hand you the walkthrough, the roofline is square, the vents are clear, and the gutters drain where they should.

  • 11 years serving Akron and Summit County, founded in 2015
  • EPA Lead-Safe Certified for pre-1978 homes
  • James Hardie Preferred Contractor and CertainTeed Master Craftsman trained
  • Vinyl Siding Institute Certified Installer standards on every panel
  • State of Ohio Contractor License and BBB Accredited
Get Started Today
Eleven years on Akron rooflines

What Akron homeowners say

Real experiences from customers who chose our Soffit and Facia Installation services.

“Our gutters were pulling away from the house and I figured it was just the hangers. Turned out the fascia board behind them was soft all along the back. They showed me the rafter tail with a moisture meter, replaced the bad wood, and put up new vented soffit. Two days, and the gutters have not moved since.”

D

Denise M.

Homeowner, Firestone Park

“We had squirrels in the attic for two summers. The soffit panels had gaps at every joint. The crew pulled the old panels, sealed the openings, and installed new vented soffit with tight miters. No scratching since. They also reset the gutters and ran a hose test before they left.”

R

Ray T.

Homeowner, Merriman Valley

“Our 1920s house had original wood fascia that was peeling and split. They sistered two rafter tails, wrapped everything in trim coil that matched our siding, and the roofline looks like it was always meant to be that way. The written price matched the invoice exactly.”

K

Karen L.

Homeowner, Highland Square

Frequently Asked Questions

Real answers to the questions we hear most often from local homeowners and property managers.

How much does soffit and fascia installation cost in Akron OH?
Most Akron homes run $1,800 to $4,500 for a full soffit and fascia replacement, based on 2026 pricing. A small bungalow with 120 linear feet lands near the low end; a two-story with dormers and porch ceilings pushes toward the top. Rafter repair, gutter reset, and two-story access are the three line items that move the number most. We give you a written, line-item price before any material is ordered.
What is the difference between soffit and fascia in Akron Ohio?
The fascia is the vertical board along the roof edge that your gutters attach to. The soffit is the horizontal panel underneath it that closes the gap between the roof edge and the wall. Fascia takes the weather and the gutter load; soffit handles intake ventilation and keeps animals out of the rafter bays. You need both working together, which is why we replace them as a pair.
Do I need new soffit and fascia with new siding in Akron?
Usually yes, if the fascia is soft or the soffit panels are brittle. New siding stops at the top course, so the roofline above it stays visible. If the old fascia is peeling or the soffit is chalky and cracked, it will drag down the look of the new siding. We inspect the roofline during every siding estimate and tell you honestly whether it needs replacing now or can wait.
How long does soffit and fascia last in Akron OH?
Aluminum and vinyl soffit and fascia typically last 20 to 30 years in this climate. The variable is the wood underneath. If the rafter tails stay dry and the gutters stay clear, the system holds up well. If water backs up behind ice dams every winter, you can lose a fascia board in five to seven years. Keeping gutters clear in late fall is the single biggest thing you can do.

Related Services

Siding Replacement

If your siding is chalky, cracked, or letting water behind the wall, replacing it at the same time as the soffit and fascia saves you scaffolding costs. We do both in one mobilization so the roofline and the walls match.

View Siding Replacement

Vinyl Siding Installation

Vinyl is the most common siding we install in Akron, and it pairs cleanly with vented vinyl soffit. We color-match the trim coil to the panel so the fascia reads as a continuous edge rather than an afterthought.

View Vinyl Siding Installation

Fiber Cement Siding Installation

Fiber cement holds paint longer than vinyl and stands up to hail. On a fiber cement job, we spec a heavier fascia board to carry the extra weight of the siding above the gutter line and keep the rake edge straight.

View Fiber Cement Siding Installation

Wood Siding Installation

Wood siding needs a roofline that sheds water properly, or the top courses rot first. New soffit and fascia with a folded drip edge keeps runoff off the wood and extends the life of the siding below it.

View Wood Siding Installation

Engineered Wood Siding Installation

LP SmartSide and similar engineered wood products take paint well and resist impact. We install them with the same attention to the roofline, because a failed fascia board will wick water straight into the top course of any panel.

View Engineered Wood Siding Installation

Aluminum Siding Installation

Older Akron homes often have dented aluminum siding that can be repaired or replaced. When we are already on the roofline, we can address loose panels and faded trim at the same time and save you a second setup.

View Aluminum Siding Installation

Get your soffit and fascia installation Akron OH quote

We are licensed, insured, and BBB Accredited, and we have been working Akron rooflines since 2015. Call (330) 567-4711 and we will set a time to walk your roofline, take photos, and hand you a written price. No deposit, no pressure.

Call (330) 567-4711 Get Free Estimate

Contact Apex Siding Akron

Call (330) 567-4711 or email info@apexsidingakronoh.com and we will get back to you the same business day. We answer the phone Monday through Friday, 8 a.m. to 6 p.m., and we check messages Saturday morning. Storm damage after hours? Leave a message and we will call you first thing.

Or call us right now at (330) 567-4711 — we answer.

Apex Siding Akron oh


  • Address

    1789 Killian Rd, Akron, OH 44312

  • Hours

    Mon–Fri: 7AM – 7PM
    Sat: 8AM – 4PM
    Sun: Emergency Only
    24/7 Emergency Available

Call (330) 567-4711 Get Quote
Call Quote